|
| STANDARD EQUIPMENT |
| Hoist rated capacity |
60,000 lbs. |
| Main frame |
8" x 4" x 1/2" A500 C tubing |
| Sub frame |
4" x 2" x 1/4" A500 C tubing |
| Front stop |
1 - 1/2" plate |
| Container lock |
Automatic spring loaded |
| Lift cylinder shaft |
2 - 1/2" solid steel |
| Rear hinge shaft |
3" solid steel |
| Cable |
7/8" (6 x 37 EXIWRC) |
| Cable sheaves |
10" O.D. Bronze-bushed sheave |
| Cable anchor |
4 cable clamps |
| Cable end |
Steel casting |
| Rear hold down |
1" plate located for std. containers |
| Middle hold down (IO & IOX Models) |
3/4" plate |
| Lift Cylinders |
6" x 72" D.A. |
| Reeving cylinders |
7" x 80" D.A. |
| Direct mount pump |
Gear types 35 GPM @ 1500 RPM |
| Operating pressure |
1850 PSI |
| Hydraulic valve |
2 spool 45 GPM safety bypass |
| Hydraulic reservoir |
60 gal. 25 micron filter & screen filter |
| Outside rollers |
4" O.D. with bronze bearing |
| Inside rollers (IO Models) |
6" O.D. hardened roller & pins |
| Working points |
Greaseable |
| Safety stand |
Factory installed |
| I.C.C. Bumper |
Folding, mounting lugs factory installed |
| Rear Bumper |
Pre-drilled bolt mount - sealed beam backup, clearance
and tail lights |
| Hoist up |
30 sec. approx. |
| Hoist down |
15 sec. approx. |
| Cable in |
46 sec. approx. |
| Cable out |
37 sec. approx. |
| Container length |
18' - 22'
|
| Approximate weight |
6100 lbs. |
| Back-up alarm |
Steam cleanable, 97 decibel, meets OSHA/state reg. |
| Mud flaps |
Flex rubber, bolt-on |
| Tail frame (ORX & IOX Models) |
3" x 7" A500 C tubing with (2) 1/2" |
| Hydraulic valve |
3 spool 45 GPM safety bypass (EX Models) |
| Cable end (HH Models only) |
Steel casting, knuckle-type |
| Rear flange roller (HH Models only) |
8" O.D. hardened with 2 1/2" c-1045 shaft |
| Rear center sheave (HH Models only) |
8" O.D. hardened |
| Mid-body light kit |
|
Page Top
| OPTIONAL EQUIPMENT |
| Hoist rated capacity |
75,000 lbs |
| 75,000 lb. Capacity cable |
1" (6 x 37 EXIWRC) |
| Lift Cylinder - T Models |
6" x 72" (5.5" x 4.5" x 3.5"
x 125")
Telescopic Cylinders |
| Drop-center cylinder mounting shaft |
|
| Inside controls |
Direct connect, cable or pneumatic |
| 4 Spool valve |
|
| Remote mount hydraulic pump |
Gear type 35 GPM @ 1500 RPM |
| Auxiliary fold down front stops |
For short containers |
| "Drop-in" Stops |
|
| Cab Guard |
|
| Full fenders |
Tandem or tri-axle, 12 ga. steel or poly |
| Hoist alarm |
|
| Tarp Rack / tool box combination |
20" x 16" x 48" |
| PTO air operated with signal light |
|
| * Single - acting hydraulic line to rear |
* NOTE: This requires the
3 spool valve option or selector valve. |
| * Double - acting hydraulic line to rear |
| * Double - acting hydraulic line to side |
| Vernier throttle kit (remote) |
|
Page Top |
